Pacific Beer Equipment' renowned high-tech Draught Foam Control device, the DFC9500, stops beer flow immediately after a keg empties, both at the key and the tap. This eliminates the spitting and spraying that usually happens when a keg "blows". And because the DFC9500 keeps the supply lines full of beer, even when a keg blows, you get instant beer from a freshly tapped keg. That's right - no more time and money is wasted pouring off foam in order to get to the good stuff.Savings for businesses are astronomical. Independent testing by various North American Breweries has shown the DFC9500 saves an average of one pitcher of beer per keg on a typical long-draw run, even greater savings for stadiums, airports, and hotels. Given that there are approximately 40 pitchers in a keg and based on a volume of 40 kegs per week - bars, pubs, clubs and restaurants would save one keg a week. That's 52 kegs a year! Owners see the return on their investment very quickly.
The DFC9500 is available as a wall mount unit, using Pacific Beer Equipments own wall mount bracket or keg mounted. The wall bracket mounts to the cooler wall with two screws and you simply slide the DFC9500 onto the bracket, facing either left or right,depending on the layout of the cooler and the orientation of the trunk lines.

The original DFC9500's composition and design have been carefully studied by the Canadian Plastic's Institute and all of their recommendations have been implemented in the design of DFC9500.
Our use of the high quality "Engineering Grade" plastics, and design modifications, recommended by the Institute have made the DFC9500 extremely durable and strong. Although we don't recommend it, the DFC9500 is strong enough to lift a full keg off of the ground.
The DFC can be fitted with any one of five(5) different base configurations.(see below for details)
Easy to operate. After changing keg's beer flow can be restored with the twist of the wrist.
Simple installation takes less than five minutes.
The DFC9500's non intrusive design allows it to be installed without having to make changes to the existing system (cutting into supply lines, new fittings etc.).
Installation can be done directly on the keg connector.

Benefits

The DFC9500 stops beer flow instantly when a keg empties, keeping the supply line full of beer. Beer is no longer wasted as foam when a new keg is tapped. Save an average of one pitcher of draught per keg. Much greater savings is seen at installations with longer than average supply lines like Stadiums, Airports, and Hotels.
Reduces the amount of CO2 or Beer Gas used because it no longer fills the supply line and escapes out of the tap.
Ideal for installations with computer portion control, and flow metering systems, which can lose Calibration and give inaccurate total volume readings when gas passes through them.
Bartenders require less time to change kegs because the supply lines do not need to be cleared of gas and foam to get to "clear" beer. Servers do not have to wait to have their orders filled.
Keeping the supply lines constantly full of beer reduces the amount of contaminants i.e. beerscale, and sludge, which forms in lines faster when exposed to air. As a result supply lines remain cleaner and beer tastes fresher between cleanings.
The DFC9500 has a low interior volume and injector tubes that maintain agitation throughout the chamber. This inhibits the buildup of deposits inside the unit.
The DFC9500's can be locked into an 'open' position and remain on the keg connector or when the supply lines are being cleaned. Cleaning solutions can be sent through the unit in either direction
Manual hand cleaning is easy because the DFC9500 can be completely taken apart and put back together in a few minutes. This design also makes servicing the units, if necessary, quick and easy.

Here at Pacific West Technologies, we offer several styles of bases that will meet the demands of a highly diverse marketplace. We now have five base configurations available, with more on the way! With the variety of bases we have to offer, one of them is bound to meet yours and your customers' needs.

Keg Mount Base
F10/M10:  5/8'' female inlet & 5/8'' male outlet
F8/M8: 1/2'' female inlet & 1/2'' male outlet
F8/FJG6: 1/2'' female inlet with 3/8'' John Guest SpeedFit on the outlet.

Wall Mount Base
M/M: 5/8'' male inlet & outlet
FJG6/ FJG6: 3/8'' John Guest SpeedFit on the inlet & the outlet. Accepts 3/8 ''O.D. tubing.

Foaming at the end of a keg and when starting a new keg cost bar operators profit from beer wastage at keg change over. Since the DFC9500 keeps the supply lines full during keg change over, this waste and subsequent loss of profit is eliminated. Average potential savings per keg change are illustrated below.

Using a 3/8 inch Supply Line
10 ft 6 oz
30 ft 18 oz
100 ft 50 oz (2.5 pints)
150 ft 75 oz (Almost 4 pints!)

Your new DFC9500 is warranted for two (2) years from the date of original purchase against all defects in workmanship and/or materials. Parts that prove defective during the two (2) year period will be either repaired or replaced at our option . The right is reserved by the manufacturer to replace the whole product in lieu thereof.The warranty does not apply if the damage occurs because of accident, improper handling, shipping damage, abuse, misuse, unauthorized repairs made or attempted and cleaning methods not approved by the manufacturer.This warranty is in lieu of any other warranty either expressed or implied. If service is required, please contact your nearest authorized distributor/installer of the DFC9500.